How do you calculate HP for a submersible pump?

motor current = 130 amps full load Horsepower loss in #00 cable = H.P. loss per 100′ x Total Cable Length = . 65 x 214 = 1.39HP 100 100 g. Total Horsepower: = Bowl horsepower + Thrust HP loss + Cable horsepower loss = 98.54 + 1.39 + . 17 = 100.10 H.P. (100 H.P.

How high can a 1hp submersible pump lift water?

a 1 hp. submersible well pump – varying by model – can deliver 10 gph while lifting water from a 200 ft. deep well. a 1 hp submersible well pump – varying by model – can deliver 23 gpm at 40 foot lift, down to 14 gpm if that same pump has to lift water from greater depth.

How far can a 1 hp submersible pump push water?

A deep-well jet pump also sits above ground, but it draws water through the use of two pipes — one to draw water from the well and the second to push water upward. The deep-well jet pumps are designed to extract water from depths up to 110 feet and require a foot valve to prime the pipe.

How much HP do I need a water pump to lift water to a height of 60 feet?

Example – Horsepower Required to Pump Water

Power Required to Pump Water (hp)
Volume Flow (gpm)	Height (ft)
45	0.0568	0.568
50	0.0631	0.631
60	0.0758	0.758

How do I calculate horsepower?

The equation to calculate horsepower is simple: Horsepower = Torque x RPM / 5,252.

How do you calculate pump horsepower?

Use this equation to help figure out what electric motor horsepower (HP) is required to drive a hydraulic pump. SImply take the gallons per minute (GPM) multiplied by the pump pressure PSI then divide that number by the result of 1,714 times efficiency (we used 85\% effiencey in this case).

How do you calculate water lift?

On a suction lift, the total dynamic suction lift is calculated by adding the static suction lift plus the friction loss at flow rate. On a system with the water higher than the pump, the total dynamic suction lift is calculated by subtracting the friction loss from the positive inlet pressure or static head.

How do you calculate pump suction lift?

The equation for determining how much of a suction lift you can pull with your pump you can take your Atmospheric pressure(Pb) subtract your Pump NPSHR, Vapor Pressure (Vp), friction losses (hf) and NPSH Margin (Safety factor) and you will have your maximum suction lift.

How do you calculate submersible pump size?

The submersible pump stage calculation tells you how many stages are required. You find it by dividing the total dynamic head (TDH) by the length of each stage. The TDH is the equal to the sum of the pumping level, head length, drop pipe friction loss and check value friction.

What is the capacity of 1.5 hp submersible pump?

1.5 Hp Single Phase V4 submersible pump, Capacity: 15 To 50 M

Motor Horsepower	1.5 Hp
Motor Phase	Single Phase
Discharge Outlet Size	50 mm or 2 inch
Capacity	15 to 50 m
Maximum Discharge Flow	100 – 500 LPM

How is motor horsepower calculated?

How much HP is required to lift water to different heights?

How much Horsepower HP is required to Lift Water to Different Heights. Horsepower theoretically required for pumping water equals the gallons per minute multiplied by the head in feet, and divided by 4.000 For power recommended, divide by 2000 instead of 4000.

How much horse power do I need to pump water?

Horsepower theoretically required for pumping water equals the gallons per minute multiplied by the head in feet, and divided by 4.000 For power recommended, divide by 2000 instead of 4000.

How much power do I need to run a submersible pump?

If there’s no power on site, you need to spec a generator: •Most submersible pumps with 5HP or less are 230V/single phase. You’ll need 1.5kW per motor HP So…a 5HP pump needs a minimum of 7.5kW You also need to spec the right power cable •PVC flat-jacketed wire is the most common.

What is the formula to calculate the hydraulic horse power?

h = differential head (m) p = differeential pressure (N/m2, Pa) The hydraulic Horse Power can be calculated as: Ph (hp) = Ph (kW) / 0.746 (2)